3D Printing – Viking Armory

Glock Slide Vises!

Wish you had a 3^rd hand to hold your Glock slide while you are working on it? Trying to adjust your sights or add an optic? This tool is for you. There are 3 models one for each slide type/size.

The images here might show different slide sizes, the tool functions the same for all of them.

After you separate your slide from the frame, you slide the block in from the back of the slide. It will be a snug fit, you might have to pinch the sides to get it to slide in.

You do not need to remove any parts from your slide to get it to work. In most cases you are going to want to keep the block to the back of the slide, where most of your work is going to be done.

Glock Slide Block showing the adjustment screw

The Glock slide tool is made from non-marring plastic that is softer than the slide. Over time is will wear and become loose, to correct that, I added a tightening screw. As you thread it in it will spread holding the slide tighter.

With the barrel and recoil spring removed the Glock slide block can be used at any position on the slide.

Thanks for looking, You can buy one HERE

Glock 44 15 Round Magazine Upgrade

I want to give my Glock 44 as many rounds as my Glock 19. To do so I made some changes to the alex alex Glock 44 15 round magazine upgrade found in several places on the internet. I started with foxalex extension found on HERE on thingiverse. I added a slot for the magazine spring and side catches to help it hold better. My remix can be found HERE

I used THIS follower. Make sure it is clean with no sharp edges and overhangs.

I attached it to a Walther PPQ 22 15+1 Replacement Magazine Spring. I did not want stretch my factory spring as suggested in some of the online articles. I like to keep all my factory parts as original as I can.

Glock 44 15 round magazine follower and spring

Then I slid the spring assembly into the magazine and made sure it slid without getting caught and hanging up on anything.

Glock 44 15 round magazine spring insert and install — Glock 44 15 round magazine spring install

Slid the base back on:

For the final product:

Glock 44 15 round magazine complete — G44 15 round mag complete

I put around 100 rounds through it so far without issues. I will try and keep this post updated.

GlockSmith Block

I wanted to create a block that Glock Armorers could use to perform Glock-Smithing tasks regardless of Glock model.

GlockSmith Block Naked Showing New PinsSo far it has spots for:

– Trigger Shoe Removal and Install

– Connector Adjustments

– Trigger Jig

Showing the new pins:

– Firing Pin Spring and Cup(s) replacement

It has been working out pretty good for me. If you have suggestions or ideas hit me up using the info below.

Download HERE

Hit us up with comments or requests

All Documents posted on this site are for informational use only. If you make ANY modifications to your Weapons based on this site, you do at your own risk! If done incorrectly, you can render you weapon unsafe and / or unusable.

More HERE: https://viking-armory.com/?page_id=723

Glock Performance Trigger Tool

Putting the trigger bar back in place on Glocks performance trigger is a PITA. I created this very little tool to help out.

Instructions:

Here is a quick Video:

– Push the Trigger Spring with Sear-holder up

– Slide the Performance Trigger Tool through the round hole, opposite side of where the trigger bar will slide in

– Push the Trigger Spring with Sear-holder down, holding it in the down position ensuring the spring rod pushes on the slave pin.

– Install the trigger bar making sure that the lower extension / pin is in the Performance Trigger Tools open hole.

– Slide out the Performance Trigger Tool

Ready to install!

Buy it from our EBAY store!

Hit us up with comments or requests

DISCLAIMER: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. or GLOCK Ges.mbH. Neither Viking Armory nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.mbH. The use of “GLOCK” on this page is merely to advertise the sale of Glock parts, or components. For genuine GLOCK, Inc. and GLOCK Ges.mbH products and parts visit www.glock.com

More HERE: https://viking-armory.com/?page_id=723

Foredom Yoke

I wanted to make a Yoke assembly for my Foredom motor, something like this one.

I had this big bearing from a previous project. This led me to create 2 versions:

Big Bearing:

And a standard 608 Skate Board Bearing version:

The insert works for both:

Looks and works pretty good! I have been using the large bearing version for around 6 months with no issue. I am not a heavy Foredom user, it is a tool in my tool box.

Download HERE

Hit us up with comments or requests

Glock Safety Plunger Holder and Polishing

When polishing any small part like the Glock safety plunger using buffung wheels on my grinder the part would at times go flying out and get damaged or temporarly lost. To help with that I create and print the Glock Safety Plunger Holder. I have different versions for different models and generations:

Plunger Holder.stl:

Glock Gen 1-5 Sfty Holder — Plunger Holder.stl

Glock Gen 1-5 Sfty Holder Reverse — Plunger Holder.stl

Gen 5:

Plunger Holder Shallow.stl

Glock Gen 1-5 Sfty Holder Shallow — Plunger Holder Shallow.stl

Glock Gen 1-5 Sfty Holder Shallow Reverse — Plunger Holder Shallow.stl

Gen 5:

Plunger Holder with Lip.stl – I am testing this one out. I added the lip to see if it would help hold the Glock Safety Plunger a bit better…

Glock Gen 5 Sfty Holder with lip Gen 5 — Plunger Holder with Lip.stl

Plunger Holder G43 G48.stl

Glock G43-G48 Sfty Holder — Plunger Holder G43 G48.stl

Plunger Holder G43 G48 Shallow.stl

Glock G43-G48 Sfty Holder Shallow — Plunger Holder G43 G48 Shallow.stl

Plunger Holder G43 G48 Reverse.stl

Glock G43-G48 Sfty Holder Reverse — Plunger Holder G43 G48 Reverse.stl

Plunger Holder G43 G48 Reverse Shallow.stl

Glock G43-G48 Sfty Holder Shallow Reverse — Plunger Holder G43 G48 Reverse Shallow.stl

I usually print these up when I have just a bit of filament left. Then toss it in a drawer till needed.

Hit us up with comments or requests

https://www.thingiverse.com/thing:5926916

More HERE: https://viking-armory.com/?page_id=723

Glock 48 Dry Fire Thing

I want to do some dry fire training without having to rack the slide each time. I created my own version of the zip tie or cardboard hack for Glocks. Google it, lots of info out there.

It is a low profile and in my opinion a bit ‘cleaner’ so I can use all my holsters, without any other changes to the weapon.

With this method, the trigger no longer has reset and break. Instead it just moves freely back and forth. It is not ideal, but allows dry fire training without cycling the firearm.

Hit us up with comments or requests

More HERE: https://viking-armory.com/?page_id=723

Glock Trigger Jig Update

I did not like the way the trigger housing moved when manipulating the trigger. So I added a brace. I printed it with tree supports that need to be cleaned up before using it.

Works pretty good!

Download HERE

Hit us up with comments or requests

More HERE: https://viking-armory.com/?page_id=723

Glock 48 Rail Mount

The glock 48 front rail is smaller than standard rails making it much harder to find anything that fits it. To help remedy this I made two slide over versions:

Picatinny: