Glock Safety Plunger Polishing

Here are some shots of Glock Safety plungers I polished using the method I wrote about here:

https://viking-armory.com/?p=585

Generation 1-4:

Glock Generation 1-4 Safety Plunger
Glock Generation 1-4 Safety Plunger
Glock Generation 5 Safety Plunger
Glock Generation 5 Safety Plunger

Generation 5:

Glock Generation 5 Safety Plunger
Glock Generation 5 Safety Plunger
Glock Generation 1-4 Safety Plunger
Glock Generation 1-4 Safety Plunger

Glock 43 and 48

Glock 43 and 48 Safety Plunger

Glock 43 and 48 Safety Plunger
Glock 43 and 48 Safety Plunger

Hit us up with comments or requests

All Documents posted on this site are for informational use only. If you make ANY modifications to your Weapons based on this site, you do at your own risk! If done incorrectly, you can render you weapon unsafe and / or unusable.

More HERE: https://viking-armory.com/?page_id=723

Glock Polish Job – Firing Pin

Using the polishing items in the notes HERE I did the example below:

Here are is a before shot:

Glock Firing Pin Polish Before shot

I am trying to show the firing pin face in this one. Notice the grooves:

Glock Firing Pin Face Before

General Cleaning / Shine polish to all areas. Careful not to remove too much from the YELLOW areas and the firing pin tip.

Glock Firing PinBase Polish right Glock Firing PinBase Polish left

The Face  area is what you want to get butt ass smooth.

Glock Firing Pin Face After

All Documents posted on this site are for informational use only. If you make ANY modifications to your Weapons based on this site, you do at your own risk! If done incorrectly, you can render you weapon unsafe and / or unusable.

More HERE: https://viking-armory.com/?page_id=723

Glock Safety Plunger Holder and Polishing

When polishing any small part like the Glock safety plunger using buffung wheels on my grinder the part would at times go flying out and get damaged or temporarly lost. To help with that I create and print the Glock Safety Plunger Holder. I have different versions for different models and generations:

Plunger Holder.stl:

Glock Gen 1-5 Sfty Holder
Plunger Holder.stl
Glock Gen 1-5 Sfty Holder Reverse
Plunger Holder.stl

Gen 5:

Glock Gen 1-5 Sfty Holder with Gen 5
Plunger Holder.stl

Plunger Holder Shallow.stl

Glock Gen 1-5 Sfty Holder Shallow
Plunger Holder Shallow.stl
Glock Gen 1-5 Sfty Holder Shallow Reverse
Plunger Holder Shallow.stl

Gen 5:

Glock Gen 1-5 Sfty Holder Shallow with Gen 5
Plunger Holder Shallow.stl

Plunger Holder with Lip.stl – I am testing this one out. I added the lip to see if it would help hold the Glock Safety Plunger a bit better…

Glock Gen 5 Sfty Holder with lip Gen 5
Plunger Holder with Lip.stl

Plunger Holder G43 G48.stl

Glock G43-G48 Sfty Holder
Plunger Holder G43 G48.stl

Plunger Holder G43 G48 Shallow.stl

Glock G43-G48 Sfty Holder Shallow
Plunger Holder G43 G48 Shallow.stl

Plunger Holder G43 G48 Reverse.stl

Glock G43-G48 Sfty Holder Reverse
Plunger Holder G43 G48 Reverse.stl

Plunger Holder G43 G48 Reverse Shallow.stl

Glock G43-G48 Sfty Holder Shallow Reverse
Plunger Holder G43 G48 Reverse Shallow.stl

I usually print these up when I have just a bit of filament left. Then toss it in a drawer till needed.

Hit us up with comments or requests

https://www.thingiverse.com/thing:5926916

All Documents posted on this site are for informational use only. If you make ANY modifications to your Weapons based on this site, you do at your own risk! If done incorrectly, you can render you weapon unsafe and / or unusable.

More HERE: https://viking-armory.com/?page_id=723

Reddit
error: Content is protected !!