Pistols – Viking Armory

Glock Performance Trigger (GPT) Polish | Cleanup

DETAILS

The GLOCK Performance Trigger meets the criteria for those looking for an enhanced trigger pull and ergonomics, all while utilizing a flat-faced trigger and maintaining the same safety features of the GLOCK Safe Action System.

The GLOCK Performance Trigger is now compatible with 9mm Gen4 pistols. A Gen5 slide cover plate now ships with all GLOCK Performance Triggers, as an included replacement for Gen4 models that ensures compatibility and proper function. The GLOCK Performance Trigger will not come installed on any factory models. It is available as an accessory only and must be installed by a certified GLOCK Armorer. GLOCK does not recommend any aftermarket modifications to the GLOCK Performance Trigger.

Trigger Pull Weight: ∼ 5lbs.

Fits: Gen4 and Gen5 models G26, G19, G17, G34 and models G19X, G45, G47

Glock Performance Trigger factor packaging

Here is a picture of the housing and connector as it is out of the box.

Glock Performance Trigger factory housing

After a little work this is the polish I got on the trigger bar.

Other side.

Pay special attention to the surface that rubs the connector.

Glock Performance Trigger Bar connector surface

Also extra attention should be applied to the surface touching the safety plunger. Remember, you a polishing, careful not to remove too much material.

Glock Performance Trigger Bar Safety Bump

The factory Trigger shoe comes apart the same as all Glock trigger shoes.

I modify the safety as I describe HERE

Glock Performance Trigger Safety Modified

Then put it all back together and install it!

Go Shoot!

GlockSmith Block v2

I want to provide an update to the GlockSmith block . With this version it has a trigger jig and small parts storage. You can remove and install the trigger pin, remove and install the firing pin cups, adjust your connector.

Also included are top and side working pin storage

GlockSmith Block v2 with top pin storage

I added pin storage on the side. I put them there when I am done.

GlockSmith Block v2 with side pin storage

Modified all the pin holes so the factory pins can be used and wont fall all the way through.

GlockSmith Block v2 trigger with factory Glock pin

GlockSmith Block v2 trigger removal with factory Glock pin

You can use the Glock pins I sell

GlockSmith Block v2 trigger removal with our Glock pin

or the factory pins:

This works for all the pin holes.

You can pick one up HERE

Get the pins with it HERE

Glock Maintenance Pins

These are great if you need to test and disassemble your Glock frame multiple time in one sitting. Such as adjusting your trigger shoe, trigger housing, or adjusting your connector.

They can be used to dry fire your Glock, to check to see if more changes are required. If there are, you can use the handle to easily remove the pins and make your adjustments.

DO NOT use for live fire!

When you are done, you can push them out with the factory pins or pull them out and install your factory pins and head to the range.

Pickup your set HERE

Pistol Deep Cleaning!

This is what I do for deep cleaning my pistols. I don’t want to get into the endless debate over how and when you should clean, that’s up to you. I am only showing what I do.

This is a shot of my setup before initial take down.

I use my Harbor Freight ultra sonic cleaner with a 30:1 ratio of distilled water:Simple Green set on heat for 16 minutes. 8 minutes flip / adjust parts another 8 minutes. Small parts go into a jar or solution filled zip lock bag.

Gun Cleaning Simple Green HF Ultra Sonic

Then I blow everything off:

Then I drop the parts in my Bald Eagle ultra sonic cleaner with a 20:1 ratio of Distilled water:Ballistol set on 122 degrees for 20 minutes. 10 minutes flip / adjust parts another 10 minutes. I put the small parts in a jar with the same solution.

I blow and wipe everything off then lay the parts out back on the work bench.

Then I put it back together and function test. Ready for the range.

Glock Slide Vises!

Wish you had a 3^rd hand to hold your Glock slide while you are working on it? Trying to adjust your sights or add an optic? This tool is for you. There are 3 models one for each slide type/size.

The images here might show different slide sizes, the tool functions the same for all of them.

After you separate your slide from the frame, you slide the block in from the back of the slide. It will be a snug fit, you might have to pinch the sides to get it to slide in.

You do not need to remove any parts from your slide to get it to work. In most cases you are going to want to keep the block to the back of the slide, where most of your work is going to be done.

Glock Slide Block showing the adjustment screw

The Glock slide tool is made from non-marring plastic that is softer than the slide. Over time is will wear and become loose, to correct that, I added a tightening screw. As you thread it in it will spread holding the slide tighter.

With the barrel and recoil spring removed the Glock slide block can be used at any position on the slide.

Thanks for looking, You can buy one HERE

Glock 44 15 Round Magazine Upgrade

I want to give my Glock 44 as many rounds as my Glock 19. To do so I made some changes to the alex alex Glock 44 15 round magazine upgrade found in several places on the internet. I started with foxalex extension found on HERE on thingiverse. I added a slot for the magazine spring and side catches to help it hold better. My remix can be found HERE

I used THIS follower. Make sure it is clean with no sharp edges and overhangs.

I attached it to a Walther PPQ 22 15+1 Replacement Magazine Spring. I did not want stretch my factory spring as suggested in some of the online articles. I like to keep all my factory parts as original as I can.

Glock 44 15 round magazine follower and spring

Then I slid the spring assembly into the magazine and made sure it slid without getting caught and hanging up on anything.

Glock 44 15 round magazine spring insert and install — Glock 44 15 round magazine spring install

Slid the base back on:

For the final product:

Glock 44 15 round magazine complete — G44 15 round mag complete

I put around 100 rounds through it so far without issues. I will try and keep this post updated.

Glock Connector polishing notes

Do a basic polish. When that is done put a very slight bevel on the face of the ledge.

Side Drawing and Picture of connector before:

Very slightly bevel the face of the ledge.

All Documents posted on this site are for informational use only. If you make ANY modifications to your Weapons based on this site, you do at your own risk! If done incorrectly, you can render you weapon unsafe and / or unusable.

More HERE: https://viking-armory.com/?page_id=723

Glock Safety Plunger Polishing

Here are some shots of Glock Safety plungers I polished using the method I wrote about here:

https://viking-armory.com/?p=585

Generation 1-4:

Generation 5:

Glock 43 and 48

Hit us up with comments or requests

More HERE: https://viking-armory.com/?page_id=723

Glock Polish Job – Firing Pin

Using the polishing items in the notes HERE I did the example below:

Here are is a before shot:

I am trying to show the firing pin face in this one. Notice the grooves:

General Cleaning / Shine polish to all areas. Careful not to remove too much from the YELLOW areas and the firing pin tip.

The Face area is what you want to get butt ass smooth.

More HERE: https://viking-armory.com/?page_id=723

Glock Performance Trigger Tool

Putting the trigger bar back in place on Glocks performance trigger is a PITA. I created this very little tool to help out.

Instructions:

Here is a quick Video:

– Push the Trigger Spring with Sear-holder up

– Slide the Performance Trigger Tool through the round hole, opposite side of where the trigger bar will slide in

– Push the Trigger Spring with Sear-holder down, holding it in the down position ensuring the spring rod pushes on the slave pin.

– Install the trigger bar making sure that the lower extension / pin is in the Performance Trigger Tools open hole.

– Slide out the Performance Trigger Tool

Ready to install!

Buy it from our EBAY store!

Hit us up with comments or requests

DISCLAIMER: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. or GLOCK Ges.mbH. Neither Viking Armory nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.mbH. The use of “GLOCK” on this page is merely to advertise the sale of Glock parts, or components. For genuine GLOCK, Inc. and GLOCK Ges.mbH products and parts visit www.glock.com

More HERE: https://viking-armory.com/?page_id=723