Hohenfelsjoe – Page 2 – Viking Armory

Johnny Glocks Evolution trigger Install

Here is a recent Johnny Glocks Evolution trigger I installed. This post is not to show how to install it or review it. There are plenty of articles on both out in the wild. This is just to show what one of my installs for this product look like:

This is what you get:

Slide it in place:

Put the pins back in:

Drop the slide back on, function check and ready to shoot!

Hit us up with comments or requests

All Documents posted on this site are for informational use only. If you make ANY modifications to your Weapons based on this site, you do at your own risk! If done incorrectly, you can render you weapon unsafe and / or unusable.

More HERE: https://viking-armory.com/?page_id=723

GlockSmith Block

I wanted to create a block that Glock Armorers could use to perform Glock-Smithing tasks regardless of Glock model.

GlockSmith Block Naked Showing New PinsSo far it has spots for:

– Trigger Shoe Removal and Install

– Connector Adjustments

– Trigger Jig

Showing the new pins:

– Firing Pin Spring and Cup(s) replacement

It has been working out pretty good for me. If you have suggestions or ideas hit me up using the info below.

Download HERE

Hit us up with comments or requests

More HERE: https://viking-armory.com/?page_id=723

Glock Polish Job – Firing Pin

Using the polishing items in the notes HERE I did the example below:

Here are is a before shot:

I am trying to show the firing pin face in this one. Notice the grooves:

General Cleaning / Shine polish to all areas. Careful not to remove too much from the YELLOW areas and the firing pin tip.

The Face area is what you want to get butt ass smooth.

More HERE: https://viking-armory.com/?page_id=723

Glock Performance Trigger Tool

Putting the trigger bar back in place on Glocks performance trigger is a PITA. I created this very little tool to help out.

Instructions:

Here is a quick Video:

– Push the Trigger Spring with Sear-holder up

– Slide the Performance Trigger Tool through the round hole, opposite side of where the trigger bar will slide in

– Push the Trigger Spring with Sear-holder down, holding it in the down position ensuring the spring rod pushes on the slave pin.

– Install the trigger bar making sure that the lower extension / pin is in the Performance Trigger Tools open hole.

– Slide out the Performance Trigger Tool

Ready to install!

Buy it from our EBAY store!

Hit us up with comments or requests

DISCLAIMER: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. or GLOCK Ges.mbH. Neither Viking Armory nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.mbH. The use of “GLOCK” on this page is merely to advertise the sale of Glock parts, or components. For genuine GLOCK, Inc. and GLOCK Ges.mbH products and parts visit www.glock.com

More HERE: https://viking-armory.com/?page_id=723

Foredom Yoke

I wanted to make a Yoke assembly for my Foredom motor, something like this one.

I had this big bearing from a previous project. This led me to create 2 versions:

Big Bearing:

And a standard 608 Skate Board Bearing version:

The insert works for both:

Looks and works pretty good! I have been using the large bearing version for around 6 months with no issue. I am not a heavy Foredom user, it is a tool in my tool box.

Download HERE

Hit us up with comments or requests

Part Polishing Notes

Surface:

Glass Plate as a work Surface, Anything hard and flat

Backing:

Leather

Thin Foam

Straight on the glass surface:

320 takes the longest

400

600

800

On glass surface with foam under sandpaper:

1000

1500

2000

2500

Worksharp:

6000 purple belt

Cordless Dremel;

14000 grit diamond compound

Notes:

It will look like a rainbow, seeing copper and nickle is normal

More HERE: https://viking-armory.com/?page_id=723

Glock Safety Plunger Holder and Polishing

When polishing any small part like the Glock safety plunger using buffung wheels on my grinder the part would at times go flying out and get damaged or temporarly lost. To help with that I create and print the Glock Safety Plunger Holder. I have different versions for different models and generations:

Plunger Holder.stl:

Glock Gen 1-5 Sfty Holder — Plunger Holder.stl

Glock Gen 1-5 Sfty Holder Reverse — Plunger Holder.stl

Gen 5:

Plunger Holder Shallow.stl

Glock Gen 1-5 Sfty Holder Shallow — Plunger Holder Shallow.stl

Glock Gen 1-5 Sfty Holder Shallow Reverse — Plunger Holder Shallow.stl

Gen 5:

Plunger Holder with Lip.stl – I am testing this one out. I added the lip to see if it would help hold the Glock Safety Plunger a bit better…

Glock Gen 5 Sfty Holder with lip Gen 5 — Plunger Holder with Lip.stl

Plunger Holder G43 G48.stl

Glock G43-G48 Sfty Holder — Plunger Holder G43 G48.stl

Plunger Holder G43 G48 Shallow.stl

Glock G43-G48 Sfty Holder Shallow — Plunger Holder G43 G48 Shallow.stl

Plunger Holder G43 G48 Reverse.stl

Glock G43-G48 Sfty Holder Reverse — Plunger Holder G43 G48 Reverse.stl

Plunger Holder G43 G48 Reverse Shallow.stl

Glock G43-G48 Sfty Holder Shallow Reverse — Plunger Holder G43 G48 Reverse Shallow.stl

I usually print these up when I have just a bit of filament left. Then toss it in a drawer till needed.

Hit us up with comments or requests

https://www.thingiverse.com/thing:5926916

More HERE: https://viking-armory.com/?page_id=723

Glock 48 Dry Fire Thing

I want to do some dry fire training without having to rack the slide each time. I created my own version of the zip tie or cardboard hack for Glocks. Google it, lots of info out there.

It is a low profile and in my opinion a bit ‘cleaner’ so I can use all my holsters, without any other changes to the weapon.

With this method, the trigger no longer has reset and break. Instead it just moves freely back and forth. It is not ideal, but allows dry fire training without cycling the firearm.

Hit us up with comments or requests

More HERE: https://viking-armory.com/?page_id=723

Timney Trigger Glock Install

Here is a recent Timney trigger I installed. This post is not to show how to install it or review it. There are plenty of articles on both out in the wild. This is just to show what one of my installs for this product look like:

This is what you get:

Slide it in place:

Put the pins back in:

Drop the slide back on, function check and ready to shoot!

Hit us up with comments or requests

More HERE: https://viking-armory.com/?page_id=723

Glock Trigger Jig Update

I did not like the way the trigger housing moved when manipulating the trigger. So I added a brace. I printed it with tree supports that need to be cleaned up before using it.

Works pretty good!

Download HERE

Hit us up with comments or requests

More HERE: https://viking-armory.com/?page_id=723